Progressive Setting Plugs

Pennoyer-Dodge Company
*Progressive Setting Plug Gages
American Gage Design / Short & Long Form Calibration Reports Available
Class X Right Hand

How to Order Progressive Setting Plugs
* Progressive master setting plugs differ from conventional truncated setting plugs in that the plug member contains two distinct P.D. limit areas. The limits are based on the Min. and Max. P.D. limits for the ring gage it will be used to inspect. The front portion contains the minimum P.D. limit with a full form major diameter, while the back portion contains the maximum P.D. limit with a truncated major diameter..

1-818-547-2100
(All verbal orders must be confirmed by fax or formal P.O.)

Fax 1-818-240-5719

How To Order
1. State Quantity desired.
2. Nominal size and threads per inch and class of fit. Example:
1/4-28 UNF-2A Progressive
3. Go or Not Go or a complete double end.

4. Handles, either single end or double end. Handles ordered in colors other than Red or Green add $20.00 per handle.
5. Special marking may be added for an additional charge,($20.00 min).
6. Long Form Calibration Reports are required, add $50.00 per member.
7. Calibration stickers available @ $10.00 per sticker (advise calibration cycle).
8. "J" series thread add $10.00 per plug member.

Prices subject to change without notice.

Nominal Size	Go or Not Go 2A or 3A Members	Complete Double End Gage W/Handle	Handle Only	Handle Size
# 0-80 UNF	304.00	628.00	20.00	# 000
# 1-64 UNC	304.00	628.00	20.00	# 000
# 1-72 UNF	304.00	628.00	20.00	# 000
# 2-56 UNC	304.00	628.00	20.00	# 000
# 2-64 UNF	304.00	628.00	20.00	# 000
# 3-48 UNC	279.00	578.00	20.00	# 000
# 3-56 UNF	279.00	578.00	20.00	# 000
# 4-40 UNC	279.00	578.00	20.00	# 00
# 4-48 UNF	279.00	578.00	20.00	# 00
# 5-40 UNC	253.00	526.00	20.00	# 00
# 5-44 UNF	253.00	526.00	20.00	# 00
# 6-32 UNC	253.00	526.00	20.00	# 00
# 6-40 UNF	253.00	526.00	20.00	# 00
# 8-32 UNC	253.00	526.00	20.00	# 0
# 8-36 UNF	253.00	526.00	20.00	# 0
# 10-24 UNC	253.00	526.00	20.00	# 0
# 10-32 UNF	253.00	526.00	20.00	# 0
# 12-24 UNC	253.00	526.00	20.00	# 0
# 12-28 UNF	253.00	526.00	20.00	# 0
# 12-32 UNEF	317.00	654.00	20.00	# 0
1/4-20 UNC	213.00	446.00	20.00	# 1
1/4-28 UNF	213.00	446.00	20.00	# 1
1/4-32 UNEF	287.00	594.00	20.00	# 1
5/16-18 UNC	213.00	446.00	20.00	# 1
5/16-24 UNF	213.00	446.00	20.00	# 1
5/16-32 UNEF	315.00	650.00	20.00	# 1
3/8-16 UNC	227.00	474.00	20.00	# 2
3/8-24 UNF	227.00	474.00	20.00	# 2
3/8-32 UNEF	344.00	708.00	20.00	# 2
7/16-14 UNC	227.00	474.00	20.00	# 2
7/16-20 UNF	227.00	474.00	20.00	# 2
7/16-28 UNEF	344.00	708.00	20.00	# 2
1/2-13 UNC	247.00	514.00	20.00	# 2
1/2-20 UNF	247.00	514.00	20.00	# 2
1/2-28 UNEF	358.00	736.00	20.00	# 2
9/16-12 UNC	274.00	568.00	20.00	# 3
9/16-18 UNF	270.00	560.00	20.00	# 3
9/16-24 UNEF	363.00	746.00	20.00	# 3
5/8-11 UNC	285.00	590.00	20.00	# 3
5/8-18 UNF	270.00	560.00	20.00	# 3
5/8-24 UNEF	370.00	760.00	20.00	# 3
11/16-24 UNEF	374.00	768.00	20.00	# 3
3/4-10 UNC	319.00	658.00	20.00	# 3
3/4-16 UNF	310.00	640.00	20.00	# 3
3/4-20 UNEF	378.00	776.00	20.00	# 3
13/16-20 UNEF	423.00	866.00	20.00	# 3
7/8-9 UNC	342.00	704.00	20.00	# 4
7/8-14 UNF	324.00	668.00	20.00	# 4
7/8-20 UNEF	438.00	896.00	20.00	# 4
15/16-20 UNEF	453.00	926.00	20.00	# 4
1-8 UNC	423.00	866.00	20.00	# 4
1-12 UNF	404.00	828.00	20.00	# 4
1-14 UNS	404.00	828.00	20.00	# 4
1-20 UNEF	478.00	976.00	20.00	# 4
1 1/16-18 UNEF	501.00	1022.00	20.00	# 4
1 1/8-7 UNC	483.00	986.00	20.00	# 4
1 1/8-12 UNF	455.00	930.00	20.00	# 4
1 1/8-18 UNEF	501.00	1022.00	20.00	# 4
1 3/16-18 UNEF	530.00	1080.00	20.00	# 5
1 1/4-7 UNC	530.00	1080.00	20.00	# 5
1 1/4-12 UNF	510.00	1040.00	20.00	# 5
1 1/4-18 UNEF	530.00	1080.00	20.00	# 5
1 5/16-18 UNEF	576.00	1172.00	20.00	# 5
1 3/8-6 UNC	610.00	1240.00	20.00	# 5
1 3/8-12 UNF	569.00	1158.00	20.00	# 5
1 3/8-18 UNEF	585.00	1190.00	20.00	# 5
1 7/16-18 UNEF	632.00	1284.00	20.00	# 5
1 1/2-6 UNC	580.00	1180.00	20.00	# 5
1 1/2-12 UNF	580.00	1180.00	20.00	# 5
1 1/2-18 UNEF	634.00	1288.00	20.00	# 5